Discovering Plumbing Basics is Crucial for Installing a Bathtub
Discovering Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
The article author is making several good pointers on the subject of Installing A Bathtub overall in this post further down.
Installing a bath tub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is likewise a moderately tough task. If the old bathtub is readily accessible, the job can move easily; if you need to open up a wall surface to remove the old tub and place the brand-new bath tub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and also fit trying it. Rather than employing a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might require an expert plumber to make tube links.
This post will certainly help you mount a brand-new bath tub in your bathroom if you have currently purchased a new tub as well as don't need to transform the setup of your previous supply of water pipes.
Your tools and also product checklist need to consist of the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to avoid pressure on the bathtub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final setting.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub up until the spirit level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water and check all joints and also brand-new pipework for leaks and tighten them if needed. Fill the bath tub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the tub must wait till the tub has been used at the very least once as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Secure the faucet in place with the producer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing difficulties with dampness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can fracture rather early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily readily available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that review about How to Install a Bathtub while surfing the internet. Loved our content? Please share it. Help other people check it out. Kudos for your time. Kindly come by our website back soon.
Quality fix? Call! Report this page